Design And Construction Of A 16-Way Clap Operated Switch
This research work on “Design And Construction Of A 16-Way Clap Operated Switch” is available in PDF/DOC. Click the below button to request or download the complete material
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
Keyword: 16-way clap operated switch, project on clapping switch, uses of clap switch, pcb of clap switch, clap switch project report, how to make a clap switch on breadboard, clap switch using transistor, clap switch for home appliances, clap based fan switching system.
Clap Operated Switch Circuit
This circuit is built around timer IC 555 (IC1), CMOS IC 74LS93 (IC2) and five BC547 npn transistors (T1, T2, T3, T4 and T5). Transistor T1 is used as the pre-amplifier and the rest are used for driving the relays.
Circuit Diagram: Clap Operated Switch
A small condenser microphone is connected at the base of transistor T1, which is biased from resistor R1 (10 kilo-ohms). The clapping sound is converted into electrical energy by the microphone and amplified by transistor T1. The transistor output is fed to the monostable circuit wired around IC 555. Output pin 3 of the timer is connected to the clock input of divide-by-16 IC 74LS93.
The outputs of IC2 are fed to npn transistors T2, T3, T4 and T5 via 100ohm resistors to drive relays RL1, RL2, RL3 and RL4 connected to appliances 1 though 4, respectively. Freewheeling diodes D1 through D4 connected across the relays protect the transistors from the back electromagnetic field (e.m.f.) produced by the relays.
The output states of IC 74LS93 (Q0 through Q3) for different numbers of claps are shown in the table.
Construction & testing
The circuit is powered from regulated 5V DC. For testing the circuit, disconnect the resistors from the outputs of IC2 and connect four LEDs in series with 220-ohm resistors between the outputs and ground. Now switch on the power supply and clap near the microphone. You can see the four LEDs glowing in the manner shown in the table. A reset push switch is provided to switch off all the ‘on’ devices.
Now you can connect the desired appliances to the relays and control them with your claps.
A 150–300 word synopsis of the main objectives, methods, findings, and conclusions of the Design And Construction Of A 16-Way Clap Operated Switch should be included in the abstract.
Every chapter, section, and subsection in the research work should be listed in the Table of Contents, including the page numbers that correspond to each one.
The background, research question or hypothesis, and objective or aim of the Design And Construction Of A 16-Way Clap Operated Switch should all be presented in the introduction, which is the first section.
A survey of previously conducted research on Design And Construction Of A 16-Way Clap Operated Switch should be included in the literature review, together with an overview of the main conclusions, a list of any gaps, and an introduction to the current study.
The conclusion part should address the implications of the study, provide an answer to the research question and summarize the key findings.
The reference of Design And Construction Of A 16-Way Clap Operated Switch, which should be formatted following a particular citation style (such as APA, MLA, or Chicago), is a list of all the sources cited in the title.
Other important sections of the Design And Construction Of A 16-Way Clap Operated Switch should include the Title page, Dedication, Acknowledgments, Methodology, Results, Discussion, Appendices, Glossary, or Abbreviations List where applicable.