Pepper Grinding Machine With A Dual Power Supply (Electricity And Fuel)
This research work on “Pepper Grinding Machine With A Dual Power Supply (Electricity And Fuel)” is available in PDF/DOC. Click the below button to request or download the complete material
ABSTRACT
The aim of the project is to construct a domestic pepper grinding machine to be powered by electric and fuel through pulley and belt transmission. The project is to perform grinding on grains e.g pepper. In construction of the project, there are various factors that is being put into consideration.
i.The size specification
ii.The power of the electric motor to be used
iii.The domestic operation which can be performed by the machine.
iv.The capacity of the machine.
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
1.1 RESEARCH PROBLEMS
1.2 JUSTIFICATION OF STUDY
1.3 OBJECTIVES OF THE STUDY
1.4 SIGNIFICANCE OF THE PROJECT
1.5 LIMITATION OF THE PROJECT
CHAPTER TWO
2.1 LITERATURE REVIEW
CHAPTER THREE
3.1 METHODOLGY
3.2 MAJOR PART OF THE SYSTEM
3.3 PICTURE OF GRINDING MACHINE
3.4 DOS AND DON’TS FOR SAFE GRINDING
CHAPTER FOUR
4.1 TESTING AND RESULT
4.2 CONSTRUCTION PROCEDURE AND TESTING
4.3 ASSEMBLING OF SECTIONS
4.4 ECONOMIC OF THE PROJECT
4.5 PROJECT VIABILITY
4.6 RELIABILITY
4.7 MAINTAINABILITY
4.8 PROJECT EVALUATION
4.9 GRINDING LAWS
CHAPTER FIVE
5.1 CONCLUSION
5.2 RECOMMENDATION
5.3 REFERENCES
CHAPTER ONE
1.1 INTRODUCTION
Every year, the final year student of this institution in Higher National Diploma (HND) and the National Diploma (ND) into practice.
This is aimed at justifying the emphasis lead on practical work during the course of study in the assigned to construct a pepper grinding machine by the machine committee of Mechanical Engineering Department, the Polytechnic, Enugu.
A pepper grinding machine is an equipment used for grinding pepper and which can also grind other good crops. This equipment comprises essentially of an electric motor, belt, pulley, transmission shaft, hopper, mills, spiral conveyor and stands. These alleviate the rigours and problems house we encounter when grinding beans for the good stuff.
1.2 RESEARCH OBJECTIVE
The project research objective are:
- To construct a local fabricated pepper grinding machine using available local technology.
- To construct a machine with a size specification.
iii. To construct a machine which can perform a domestic operations.
- To construct a machine which have adequate capacity, lighter in weight, lesser fatigue and portable.
1.3 JUSTIFICATION OF STUDY
- This is to promote indigenous machine and their producers.
- To have a portable pepper grinding machine constructed for domestic uses with a powered driven source.
iii. To improve the economic and the country as a whole by neglecting imported blenders i.e producing machine that is affordable to substitute the imported blenders.
- To be able to meet National Board for Technical Education (NBTE) requirement in awarding National Diploma (ND) in Mechanical Engineering.
1.4 OBJECTIVES OF THE STUDY
The objectives of the study are:-
- To construct pepper grinding machine with local materials.
- To construct a machine which is less in crop and domestic usage.
iii. To produce a pepper grinding machine that is lesser in vibration, weight and in size.
1.5 SIGNIFICANCE OF THE PROJECT
-It’s fast and can grind pepper as finely as any other mill I’ve used. It also can make fantastic cracked pepper because the coarse settings are easy to adjust.
-It can grind far more than just wheat.
-It doesn’t heat up the pepper like other wheat grinders can.
-It doesn’t spew pepper anywhere.
1.6 LIMITATION OF THE PROJECT
The limitations of this project are:
-It cost of production can be higher for students
-It’s noisy.
-The capacity of the hopper is smaller than other heavy-duty mills. you would need to fill the hopper more frequently than mills with a larger capacity.