Design And Implementation Of An Industrial Batch Counter

DEDICATION

This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my — for his financial support and moral care towards me.Also to my mentor — for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my — and other people. My immensely appreciation goes to my humble and able supervisor Mr. — for his kindness in supervising this project. My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. —, and Dr. —. I also recognize the support of some of the staff of — among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. — and the —. Finally, my appreciation goes to my elder sister —, my lovely friends mercy —, —, — and many others who were quite helpful.

ABSTRACT

All garages are built with a capacity which determines the number of cars it can contain at any point in time. This number of cars is counted by garage officials which takes too much of times and energy to do so. In other to solve this problem, a digital batch counter was designed. This Project ―” industrial batch counter” is a reliable circuit that takes over the task of counting number of cars entering the garage very accurately. When car enters into the garage then the counter is incremented and when car leaves the garage then the counter is decremented. The total number of cars inside the garage is also displayed on the seven segment displays. The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers. When any object pass through the IR Receiver’s then the IR Rays falling on the receivers are obstructed. This obstruction is sensed by the Microcontroller.

TABLE OF CONTENT

COVER PAGE

APPROVAL PAGE

DEDICATION

ACKNOWLEDGEMENT

TABLE OF CONTENT

CHAPTER ONE

• INTRODUCTION
• PROJECT OVERVIEW
• AIM AND OBJECTIVES OF THE PROJECT
• JUSTIFICATION OF THE PROJECT
• THE SCOPE OF THE PROJECT
• APPLICATION OF THE PROJECT
• SCOPE OF THE PROJECT
• PROJECT WORK ORGANISATION

CHAPTER TWO

LITERATURE REVIEW

2.1      OVERVIEW OF THE PROJECT

2.2      DESCRIPTION OF IMPORTANT MODULE OF THE BLOCK

2.3      POWER SUPPLY UNIT

CHAPTER THREE

METHODODLOGY

3.1      SYSTEM BLOCK DIAGRAM

3.2      SYSTEM OPERATION

3.3      SYSTEM CIRCUIT DIAGRAM

3.4      LIST OF COMPONENTS USED

3.5      CODE EXPLANATION

CHAPTER FOUR

TESTING AND RESULTS ANALYSIS

• CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
• CASING AND PACKAGING
• ASSEMBLING OF SECTIONS
• INSTALLATION OF THE COMPLETED DESIGN
• TESTING AND RESULTS
• TESTING AND RESULTS

CHAPTER FIVE

5.1 CONCLUSION

5.2      RECOMMENDATION

5.3      REFERENCES

CHAPTER ONE

1.1                                          INTRODUCTION

An industrial digital batch counter is an electronic that handles the counting and controls the number of object such as cars entering the garage and display the output on LCD display. The technique involved in the design is a simple sensor unit that senses when cars obstruct the light path. These parameters can be used to determine when cars have moved in or out of the garage. The light sensing type involves monitoring the unit with photon or optical devices; this consists of the encoder (transmission path or the source of energy) and the decoder (receiver unit that converts the light intensity to electrical signal). An LED emitter, combined with a photo detector (Light Dependent Resistor, photo transistor or infrared sensing diode) in proximity, form a very useful object called opto-coupler or opto-isolator. When the opto coupler is obstructed, the door opens and the display shows an increase or decrease of cars (depending on the path followed). This project report creates a greater picture of the industrial digital batch counter.

1.1                                                    PROJECT OVERVIEW

This Project is a reliable circuit that takes over the task of counting number of car in the garage or human entering into a room very accurately. When car enters into the garage then the counter is counted by the interference of the circuit. The total number of persons inside the room is also displayed on the LCD displays. The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers, When any object pass through the IR Receiver’s then the IR Rays falling on the receiver are obstructed , this obstruction is sensed by the Microcontroller.

1.2                   AIM AND OBJECTIVES OF THE PROJECT

The aim of this project is to demonstrate a smart device that counts the number of cars entering the garage; and prevents car from entering once the garage has reached its capacity.

1.3                         JUSTIFICATION OF THE PROJECT

The need for counting the number of car inside the garage is for statistical record, which will help the garage management take a proper account of cars; and as well, control the garage capacity from being over populated.

1.4                             THE SCOPE OF THE PROJECT

This project covers the features of the capacity monitor, the hardware description, the use of transistor, LCD and microcontroller, how the system works and its applications.

1.5                           APPLICATION OF THE PROJECT

This device has applications such as for Batch Control, Rate Indication and Totalization processes. This device offers users an up or down totalizer

1.6                                                 SCOPE OF THE PROJECT

This work composes of two sensors. If the sensor 1 is interrupted first then the microcontroller will look for the sensor 2, and if it is interrupted then the microcontroller will increment the count and switch on the relay, if it is first time interrupted.  If the sensor 2 is interrupted first then the microcontroller will look for the sensor 1, and if it is interrupted then the microcontroller will decrement the count.  When the last car leaves the garage then counter goes to 0 and that time the relay will turn off.

• PROJECT WORK ORGANISATION

This project report is organized into five chapters. The first chapter covers the introduction, aim scope and justification of the project. The second chapter talks about the technology behind the project, the description of the microcontroller, as well as the working principle of the project. Chapter three covers the methodology of the project. Chapter four discusses the designing and construction of the project, as well as other components used in designing this project. Chapter four also talks about the testing of the individual components and packaging of the project. And lastly, chapter five summarizes and concludes the project.

PROJECT DESCRIPTION

Format = Microsoft word

Chapters = 1-5 chapters

Price: N3,000.

For more information contact us through any of the following means:

Mobile No: +2348146561114 or +2347015391124

Email address: engr4project@gmail.com

Whatsapp No: +2348146561114