Construction Of Turbine Mixer
This research work on “Construction Of Turbine Mixer” is available in PDF/DOC. Click the below button to request or download the complete material
The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu.
The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which they will be used in, making out, cutting out to sizes, rolling folding, welding, body – filling, filling, glass – papering and painting. The total surface area is 10741.5CM2
The first step taken in the fabrication of ht said project was the selection of the material suitable for the construction.
The materials used in the construction were locally sourced and were selected to suit the desired purpose. The mild steel was used instead of galvanized steel due to its relative low cost.
The mild steel was located with paint to prevent corrosion attack and deterioration of the work.
The dimensions of the project were as follow 31.0CM. for the height and –21.0cm for the diameter. The volume [capacity] of the cylinder is 10,74 1.5cm3 the average speed of the turbine mixer is 125pm. The turbine mixer is manually operated a design that is meant to save cost.
INTRODUCTION
The multiple of process and mechanical variable makes fluid agitation one of the most complete unit operations. For this reason the systematic studies of underlined me chemise of mixing operation progressed slowly, quantitative design data is spores and almost innumerable agitator configuration have evolved. Though often confused, agitation and mixing are not synonymous. Agitation refers to the induced motion of a material in a specified way, usually in a circulatory pattern inside some sort of container. Mixing is the random distribution into and through one another of two or more initially separate phases. Ex A single homogeneous material such as a thankful of cold water can be agitated, but it cannot be mixed until some other material is added such as powdered soerd.
However, many processing operations depend to their success on the effective agitation and mixing of fluids. To enhance these processing operation, Experimental agitators were developed to serve a wide variety of poetical and fundamental fluid mixing problem.
Experience has revealed that reaction that recurred mixing and agitation most often cannot perform without agitators. That is why the need to discuss agitators, Agitations and mixing can not be over ruled and has to be given to student in the territory institution as project work.
Mixing is been used to perperon on uniform combination of two or more substances. The material fed to a mixer could be gasses, higuidion solids. The product that is from mixer may be homogeneous or heterogeneous substance.
THE OBJECTIVE AND THE SCOPE OF THE PROJECT
Turbine mixer is one of the important equipment found in the chemical industries. It is been applied in variety of operations in the industries and homes such as mixing of solution of liquids, solids and gases.
The main objective of the project is to construct turbine mixer that will be widely versatile in application / operation.
Title page
Letter of transmittal
Approval page
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0 Introduction
1.1 Objectives / scope of the project
CHAPTER TWO
2.0 Literature review
2.1 Agitation and mixing
2.2 Liquid – liquid agitation
2.3 Purpose of agitation
2.4 Types of mixer / mixing equipment
2.5 Application of impeller
2.6 Shaft
2.7 Baffles
2.8 Circulation rates
2.9 Mixers for plastic solids and pastes
2.10 Mixers for dry light solids [powder]
2.11 Material of construction.
CHAPTER THREE
3.0 Fabrication / modification procedure
3.1 Steps of fabrication process
3.2 Cost analysis.
CHAPTER FOUR
4.0 Discussion
4.1 Conclusion
4.2 Recommendation
4.3 Reference
4.4 Nomenclature
CHAPTER FIVE
DISCUSSION
CONCLUSSION
RECOMMENDATION
REFERENCES
APPENDIX / NOMENECLATURE
A 150–300 word synopsis of the main objectives, methods, findings, and conclusions of the Construction Of Turbine Mixer should be included in the abstract.
Every chapter, section, and subsection in the research work should be listed in the Table of Contents, including the page numbers that correspond to each one.
The background, research question or hypothesis, and objective or aim of the Construction Of Turbine Mixer should all be presented in the introduction, which is the first section.
A survey of previously conducted research on Construction Of Turbine Mixer should be included in the literature review, together with an overview of the main conclusions, a list of any gaps, and an introduction to the current study.
The conclusion part should address the implications of the study, provide an answer to the research question and summarize the key findings.
The reference of Construction Of Turbine Mixer, which should be formatted following a particular citation style (such as APA, MLA, or Chicago), is a list of all the sources cited in the title.
Other important sections of the Construction Of Turbine Mixer should include the Title page, Dedication, Acknowledgments, Methodology, Results, Discussion, Appendices, Glossary, or Abbreviations List where applicable.